China Wholesale Micro Switch Manufacturers - GNY51-1-05 – Tongda
China Wholesale Micro Switch Manufacturers - GNY51-1-05 – Tongda Detail:
GNY51-1-05
(Switch technical Characteristics):
(ITEM) |
(technical parameter) |
(Value) |
|
1 |
(Electrical Rating) | 10A 250VAC | |
2 |
(Contact Resistance) | ≤50mΩ( Initial value) | |
3 |
(Insulation Resistance) | ≥100MΩ(500VDC) | |
4 |
(Dielectric Voltage) | (between non-connected terminals) | 500V/0.5mA/60S |
(between terminals and the metal frame) | 1500V/0.5mA/60S | ||
5 |
(Electrical Life) | ≥50000 cycles | |
6 |
(Mechanical Life) | ≥100000 cycles | |
7 |
(Operating Temperature) | 0~125℃ | |
8 |
(Operating Frequency) | (electrical):15 cycles(Mechanical):60 cycles | |
9 |
(Vibration Proof) |
(Vibration Frequency):10~55HZ;(Amplitude):1.5mm;(Three directions):1H |
|
10 |
(Solder Ability): (More than 80% of immersed part shall be covered with solder) | (Soldering Temperature):235±5℃(Immersing Time):2~3S | |
11 |
(Solder Heat Resistance) | (Dip Soldering):260±5℃ 5±1S(Manual Soldering):300±5℃ 2~3S | |
12 |
(Safety Approvals) |
UL、CSA、TUV、CQC、CE |
|
13 |
(Test Conditions) | (Ambient Temperature):20±5℃(Relative Humidity):65±5%RH(Air Pressure):86~106KPa |
Use and maintenance
(1) Check the button frequently to remove the dirt on it. Due to the small distance between the contacts of the button, after many years of use or the seal is not good, the inflow of dust or various stages of engine oil emulsion will cause the insulation to be reduced or even a short circuit accident. In this case, insulation and cleaning must be done, and corresponding sealing measures must be taken.
(2) When the button is used in a high-temperature environment, it is easy to deform and age the plastic, causing the button to loosen, causing a short circuit between the terminal screws. According to the situation, a fastening ring can be added to tighten it for use during installation, or an insulating plastic tube can be added to the wiring screw to prevent loosening.
(3) For the button with indicator light, the bulb will heat up, and the plastic lampshade will be deformed for a long time, which will make it difficult to replace the bulb. Therefore, it is not suitable to be used in places where the power is on for a long time; if you want to use it, you can appropriately lower the bulb voltage to extend its life.
(4) If poor contact is found, the reason should be investigated: if the contact surface is damaged, it can be repaired with a fine file; if there is dirt or soot on the contact surface, it should be wiped clean with a clean cotton cloth dipped in solvent; if it is a contact spring If it fails, it should be replaced; if the contact is severely burned, the product should be replaced.
GNY51-1-01
(Switch technical Characteristics):
(ITEM) |
(technical parameter) |
(Value) |
|
1 |
(Electrical Rating) | 10A 250VAC | |
2 |
(Contact Resistance) | ≤50mΩ( Initial value) | |
3 |
(Insulation Resistance) | ≥100MΩ(500VDC) | |
4 |
(Dielectric Voltage) | (between non-connected terminals) | 500V/0.5mA/60S |
(between terminals and the metal frame) | 1500V/0.5mA/60S | ||
5 |
(Electrical Life) | ≥50000 cycles | |
6 |
(Mechanical Life) | ≥100000 cycles | |
7 |
(Operating Temperature) | 0~125℃ | |
8 |
(Operating Frequency) | (electrical):15 cycles(Mechanical):60 cycles | |
9 |
(Vibration Proof) |
(Vibration Frequency):10~55HZ;(Amplitude):1.5mm;(Three directions):1H |
|
10 |
(Solder Ability): (More than 80% of immersed part shall be covered with solder) | (Soldering Temperature):235±5℃(Immersing Time):2~3S | |
11 |
(Solder Heat Resistance) | (Dip Soldering):260±5℃ 5±1S(Manual Soldering):300±5℃ 2~3S | |
12 |
(Safety Approvals) |
UL、CSA、TUV、CQC、CE |
|
13 |
(Test Conditions) | (Ambient Temperature):20±5℃(Relative Humidity):65±5%RH(Air Pressure):86~106KPa |
GNY51-1-02
(Switch technical Characteristics):
(ITEM) |
(technical parameter) |
(Value) |
|
1 |
(Electrical Rating) | 10A 250VAC | |
2 |
(Contact Resistance) | ≤50mΩ( Initial value) | |
3 |
(Insulation Resistance) | ≥100MΩ(500VDC) | |
4 |
(Dielectric Voltage) | (between non-connected terminals) | 500V/0.5mA/60S |
(between terminals and the metal frame) | 1500V/0.5mA/60S | ||
5 |
(Electrical Life) | ≥50000 cycles | |
6 |
(Mechanical Life) | ≥100000 cycles | |
7 |
(Operating Temperature) | 0~125℃ | |
8 |
(Operating Frequency) | (electrical):15 cycles(Mechanical):60 cycles | |
9 |
(Vibration Proof) |
(Vibration Frequency):10~55HZ;(Amplitude):1.5mm;(Three directions):1H |
|
10 |
(Solder Ability): (More than 80% of immersed part shall be covered with solder) | (Soldering Temperature):235±5℃(Immersing Time):2~3S | |
11 |
(Solder Heat Resistance) | (Dip Soldering):260±5℃ 5±1S(Manual Soldering):300±5℃ 2~3S | |
12 |
(Safety Approvals) |
UL、CSA、TUV、CQC、CE |
|
13 |
(Test Conditions) | (Ambient Temperature):20±5℃(Relative Humidity):65±5%RH(Air Pressure):86~106KPa |
GNY51-2-200
Switch technical Characteristics
GNY51
(Switch technical Characteristics):
(ITEM) |
(technical parameter) |
(Value) |
|
1 |
(Electrical Rating) | 10A 250VAC | |
2 |
(Contact Resistance) | ≤50mΩ( Initial value) | |
3 |
(Insulation Resistance) | ≥100MΩ(500VDC) | |
4 |
(Dielectric Voltage) | (between non-connected terminals) | 500V/0.5mA/60S |
(between terminals and the metal frame) | 1500V/0.5mA/60S | ||
5 |
(Electrical Life) | ≥50000 cycles | |
6 |
(Mechanical Life) | ≥100000 cycles | |
7 |
(Operating Temperature) | 0~125℃ | |
8 |
(Operating Frequency) | (electrical):15 cycles(Mechanical):60 cycles | |
9 |
(Vibration Proof) |
(Vibration Frequency):10~55HZ; (Amplitude):1.5mm; (Three directions):1H |
|
10 |
(Solder Ability):(More than 80% of immersed part shall be covered with solder) | (Soldering Temperature):235±5℃(Immersing Time):2~3S | |
11 |
(Solder Heat Resistance) | (Dip Soldering):260±5℃ 5±1S(Manual Soldering):300±5℃ 2~3S | |
12 |
(Safety Approvals) |
UL、CSA、TUV、CQC、CE |
|
13 |
(Test Conditions) | (Ambient Temperature):20±5℃(Relative Humidity):65±5%RH
(Air Pressure):86~106KPa |
Product detail pictures:




Related Product Guide:
Reliable good quality and very good credit standing are our principles, which will help us at a top-ranking position. Adhering to your tenet of "quality 1st, purchaser supreme" for China Wholesale Micro Switch Manufacturers - GNY51-1-05 – Tongda , The product will supply to all over the world, such as: Tajikistan , Norwegian , Algeria , Insisting on the high quality generation line management and customers expert assistance, we now have designed our resolution to offer our buyers using the to start with amount getting and just after services practical experience. Maintaining the prevailing friendly relations with our buyers, we however innovate our solution lists all of the time to satisfy the brand new demands and adhere to the most up-to-date development of the market in Malta. We are ready to face the worries and make the improve to understand all the possibilities in international trade.

This company has the idea of "better quality, lower processing costs, prices are more reasonable", so they have competitive product quality and price, that's the main reason we chose to cooperate.
